EVault - How to Backup the System State from the Primary Server and Restore it to the Secondary Server on Windows Server 2008

Follow

Summary

This Knowledge Base article provides the steps to backup the System State from the Primary server and restore it to the Secondary server on Windows Server 2008 environments. If performing this procedure on Windows Server 2003, please see RDR-REFID-1462 - How to Backup the System State from the Primary Server and Restore it to the Secondary Server on Windows Server 2003 .


More Information

The following procedure should be used when the backup of the System State is to be made from the Primary (active) server and restored to the Secondary (passive) server. If the configuration of the server pair is different, please contact your i365 Support representative.

Note: The backup file at a minimum will be as large as the System Volume and therefore will require at least an equal amount of free disk space. Ensure that sufficient free disk space is available before proceeding.

Procedure

On the Primary Server

  1. On the Primary server, open a command prompt by clicking on Start -> Run , and then typing cmd and clicking on OK .
  2. Run wbadmin start systemstatebackup -backuptarget:<Drive_Letter> :
    1. If you attempt to perform a System State backup to a volume on which the System State file resides, the following error is displayed in Windows Server 2008:

      ERROR - The location for backup is a critical volume.

      Note: To fix this issue, follow the instructions contained in Microsoft Knowledge Base article http://support.microsoft.com/kb/944530

    2. If you perform the System State backup and store it on a non-critical volume, the backup will complete successfully.
  3. The backup file is created at the following location:

    <Drive_letter>:\WindowsImageBackup\<ComputerName>\SystemStateBackup\Backup Folder

  4. Copy the entire WindowsImageBackup folder from Primary server to a shared folder on the Secondary server (this is important as wbadmin expects a shared folder as a backup source location).

    Note: If the WindowsImageBackup\<ComputerName>\SystemStateBackup folder also contains backup folders corresponding to old backups, the old backups should be excluded from the copy.
On the Secondary Server
  1. Unplug the Principal (Public) and EVault Channel network cables from the Secondary server.
  2. Set the EVault Remote Disaster Recovery service to Manual using Windows Service Control Manager.
  3. Run wbadmin get versions to get the backup version:

    wbadmin get versions -backupTarget:”\\localhost\share name”

  4. Perform the System State recovery:

    wbadmin start systemstaterecovery -backupTarget:”\\localhost\share name” -version:<version id>

    For example: wbadmin start systemstaterecovery -backupTarget:”\\localhost\share name” -version:01/14/2009-12:26

  5. Once the restore is complete, perform a server reboot (multiple reboots might be required).
  6. Verify that the network IP address settings are correct and ensure that the EVault Remote Disaster Recovery Packet Filter is enabled on the Principal (Public) network adapter and disabled for all channel network adapters.
  7. In case static routes were set up, please check and correct them if necessary according to RDR-REFID-466 - How to create a static route for the EVault Channel connection in a WAN environment .
  8. Launch the Configure Server wizard and select the Machine tab.
  9. Change the Identity to Secondary and select Primary for the Active Server .
  10. Select the Channel tab and verify the correct channel IP addresses are displayed.
  11. Select the Public tab and verify the correct Principal (Public) IP addresses are displayed.
  12. Click on Finish .
  13. If in a WAN environment, open a command prompt and navigate to <install_directory>\EVault\Remote disaster Recovery\R2\Bin and run nfpktfltr getfilter (the response should be the Secondary server's Principal (Public) IP address). If the response is not the Secondary server's Principal (Public) IP address, run nfpktfltr setfilter SecondaryIP . Confirm the setting was applied by again running the nfpktfltr getfilter command.
  14. Reconnect the Principal (Public) and EVault Channel cables to the Secondary server.
  15. Set EVault Remote Disaster Recovery service to Automatic using Windows Service Control Manager.
  16. Start EVault Remote Disaster Recovery.


Applies To

EVault Remote Disaster Recovery All Versions


Related Information

RDR-REFID-1629

KBID-2366

0 out of 0 found this helpful

Comments

0 comments

Please sign in to leave a comment.